Cabinet Handle Palazzo Slim Bar Rosette

Yes. Our handles are made to order in our Paris atelier, which gives us real latitude to go beyond the catalog. We range from custom color to raised initials or a logo, from an exclusive pattern to a numbered series. Custom work remains a separate service, on top of the catalog, priced according to your project. Every request gets its own dedicated quote, which we put together as quickly as possible after your message.

Yes. Initials, a monogram, or a logo are designed into the handle's pattern and then added in relief: they're sculpted onto the master, captured in the mold, and cast with the piece. Nothing is engraved afterward, the relief is one with the handle. The modeling work and mold making are priced in the quote.

For a knob, the existing hole almost always works, it fits the M4 screw. For a pull, check that the gap between the holes matches an available center-to-center. If in doubt, measure center to center and send us the measurement, we'll confirm the right piece for you.

Yes, in the same way. These brands design their fronts to IKEA Metod's dimensions and drilling: Plum, Superfront, Reform, A.S. Helsingö, Holte, and the other workshops making fronts for IKEA cabinets. Installation is identical, free-choice drilling and M4 screws.

Palazzo Slim Bar, Rosette attaches at two points, center-to-center 128mm, 160mm, 96mm, 192mm. Measure the distance from axis to axis between your two existing holes: if it matches, the handle replaces the old one in just a few minutes. On a blank front, you choose the placement and drill to that measurement. The most common center-to-center measurements for IKEA kitchens are 96 and 128 mm for drawers, 160 mm for larger cabinets.

Yes. IKEA Metod, Pax, and Besta fronts are factory drilled for hinges and drawers, but never for handles: you choose the placement, drill, then fasten with an M4 screw, exactly like an original IKEA handle. Palazzo Slim Bar, Rosette follows this standard, like all our pieces.

Yes, always. You receive stainless steel M4 screws in several lengths to cover standard front thicknesses, along with installation instructions. They hold up well to the humidity of a kitchen or bathroom. For a nonstandard front, just ask and we will send you the right length.

The included screws cover standard fronts, roughly 16 to 25 mm thick, which covers nearly every cabinet on the market and most IKEA fronts. For a thicker front, a solid door, or a doubled-up front, all you need is longer screws: just ask and we'll send them. For a very thin front, choose the shortest screw in the bag so it doesn't poke through on the inside.

A drill or driver with a bit suited to your door or drawer front, and a Phillips screwdriver. No specialized tools required. On a thin front, a hand screwdriver is often enough, without even reaching for the drill if the hole already exists.

Center-to-center is the distance from axis to axis between the two screws. For Palazzo Slim Bar, Rosette, it's 128mm, 160mm, 96mm, 192mm. Transfer this measurement onto the front with a fine pencil, check the alignment with a level, then mark each point with an awl before drilling, which keeps the drill bit from wandering. On an IKEA kitchen, the most common center-to-centers are 96 and 128 mm for drawers, 160 and 192 mm for larger cabinets.

Installation is the same as any cabinet handle: drill the front, secure with the included screws, hand tighten, then finish with a final turn of the screwdriver. It takes just a few minutes per piece. Palazzo Slim Bar, Rosette fits existing furniture as easily as IKEA fronts, and the installation guide is included in the package.

Palazzo Slim Bar, Rosette is made to order in our Paris atelier. Allow an average of 5 to 10 business days for production, plus the carrier's delivery time depending on your address. An email with the tracking number will reach you as soon as the shipping label is issued.

Yes. 3D printing the master, molding, casting, sanding, and patina: it all happens in our Paris workshop. Our metal powders and resins come from European suppliers, and both assembly and finishing stay French. Every piece is checked by eye in our workshop before it ships.

No. Our metal handles are cast from bronze, copper, brass, or pure aluminum powders, with no added lead, no cadmium, and no mercury. The materials used comply with European RoHS directives restricting hazardous substances. You can install them in a kitchen, a child's room, or a bathroom with no risk of toxic migration.

No. The Satin Brass finish is stabilized: its look stays true to day one, without darkening or dulling. It's the choice to make if you want a tone that doesn't shift over time. Simple care, a soft, barely damp cloth followed by drying, is enough to keep its full shine.

Yes, always: stainless steel screws sized for standard 18 to 19 mm fronts, in several lengths, plus an installation guide. For a thicker or thinner front, we send the right screws free of charge, just ask.

It all depends on the finish. Patinated finishes, like Antique Bronze or Antique Copper, are alive: they keep evolving gently, and that's their whole appeal. Matte, glossy, or color finishes, like Matte Bronze, are stabilized by their surface treatment and stay put. Either way, no bad surprises: a patina won't turn green, a stable finish stays exactly as it was. And if you ever want to refresh or change a patina, we'll take the piece back into the workshop.

For metal finishes (bronze, copper, brass, aluminum), yes to both: they hold up very well against household moisture and splashes. Bioresin, on the other hand, is best kept to dry rooms. The one real contraindication, for every material, is outdoor use exposed to the elements.

Yes, for everyday use: kitchen, bathroom, bedroom, office. Cast in metal, the material doesn't warp, doesn't break under normal pulling, and withstands everyday knocks. We archive the 3D model of every piece: even years from now, we can remake one identically.

Yes, at 80%. Brass: our pieces are cold cast from 80% pure metal powder, in a mold taken from a master we 3D print at the atelier in Paris. The shine, the weight in hand, the feel of the material: everything behaves like solid metal, with a level of detail traditional casting can't achieve. Each piece is then sanded and finished by hand, patinated for the noble metals, brushed for aluminum.

Yes for metal finishes (bronze, copper, brass, aluminum), which handle household steam very well. Bioresin, more sensitive to prolonged moisture, should be avoided in these situations. On a built-in dishwasher, choose a metal material and wipe the piece down after high-temperature cycles. That is the only thing to remember for a front exposed to steam.

A soft, slightly damp cloth is enough in most cases. For a kitchen handle exposed to greasy buildup, add a drop of mild soap, liquid Marseille soap or diluted dish soap. Then wipe with a dry cloth to avoid streaks. That's all it takes day to day: no specialty product, no complicated routine.

Bronze, copper, and brass handle mild cleaners well and keep their patina thanks to the protective treatment applied in our atelier. A soft, damp cloth with a drop of mild soap covers everyday care, then a dry cloth to bring back the shine. Save diluted vinegar for occasional limescale spots only, never for routine cleaning. These patinated metals only get better with light, regular care.

Yes, on one key point. Metal finishes (bronze, copper, brass, aluminum) tolerate mild cleaners, a bit of diluted vinegar, and even household steam. Bioresin, on the other hand, should only be cleaned with a damp cloth and mild soap, no alcohol, no solvent, no concentrated vinegar. Day to day care stays simple either way, it's mainly the list of products to avoid that differs. Each product page specifies the exact care for its material.